Saturday 4 June 2011
How do I change the tail lights in a 93 taurus?
My tail light is out, and I cant seem to access the bulbs. Any help would be appreciated. Oh, and I called some auto places, not too many out there know!|||Open the trunk then remove the trim panels in front of the lights. remove the nuts (about 8 of them) pull the whole assembly out the back and you will see where the bulbs are. Change the bulb and check to make sure it works befor you reassemble. Easy to do and shouldn%26#039;t take more than 15 minutes.|||Okay when I need to get a light changed I take it to my auto mechanic that I use for all repairs on my vehicle when it is out of warranty. He then changes the bulb for me and shows me how to do it so that I can do it myself at a later time.|||Go to Pep Boys and get a Chilton%26#039;s Repair Manual. It will give you step by step instructions with pictures
2001 volkswagen new beetle need to know how to change a rear tail light?
i have looked in the owners manual and all it said was to take it a volkswagen dealer and the closest one is over 3 hours away i have the right bulb but i can figure out how to get to the old one to replace it?!?!?!?!|||INSIDE THE HATCH THERE IS AN OVAL ACCESS PANEL
BEHIND EACH LIGHT.
TAKE THAT OFF REACH IN AND YOU%26#039;LL FIND A KNOB.
TAKE IT OFF AND CAREFULLY PRY THE WHOLE LIGHT OUT.
DISCONNECT THE WIRES (JUST A PLUG) AND TAKE THE TAIL LIGHT WHERE YOU CAN WORK TO REPLACE THE BULB.
ANY CAR WASH SHOULD HAVE A REPLACEMENT.
GOOD LUCK!
BEHIND EACH LIGHT.
TAKE THAT OFF REACH IN AND YOU%26#039;LL FIND A KNOB.
TAKE IT OFF AND CAREFULLY PRY THE WHOLE LIGHT OUT.
DISCONNECT THE WIRES (JUST A PLUG) AND TAKE THE TAIL LIGHT WHERE YOU CAN WORK TO REPLACE THE BULB.
ANY CAR WASH SHOULD HAVE A REPLACEMENT.
GOOD LUCK!
96 Mustang tail lights?
Does anyone know how to change the tail light bulb in a 96 Mustang?|||This is a really crappy design by Ford for a should be easy job.
Remove the trunk lining by the light, just peel it back far enough to work.
You%26#039;ll see 4 or 5 nuts on studs. Remove the nuts.
The light will now drop out of the metal housing.
Replace bulb like you would on any other car.
Put light back in
Replace nuts.
Put lining back
Job done|||You should buy a Chilton%26#039;s or Haynes repair Manuel for your mustang. It will give advice on all repairs step by step.
Remove the trunk lining by the light, just peel it back far enough to work.
You%26#039;ll see 4 or 5 nuts on studs. Remove the nuts.
The light will now drop out of the metal housing.
Replace bulb like you would on any other car.
Put light back in
Replace nuts.
Put lining back
Job done|||You should buy a Chilton%26#039;s or Haynes repair Manuel for your mustang. It will give advice on all repairs step by step.
How do i change a brake light in a 2003 nissan murano?
and i know you have to change the bulb, i just cnt seem to get to the bults to get the tail light out. i should probably just take it to nissan hu? if you can help please let me know! thank you!|||Open the rear hatch and look for a removable interior panel near the taillight and remove it.The bulbs or speed nuts that hold the taillight assembly in place should be visible.Remove the bulb or the nuts holding the taillight in place and replace the bulb.|||The question is: How do you remove the interior panels without damaging them?
Report Abuse
How do I change the rear turn signal bulb in a 1999 Subaru Legacy wagon?
Found how to change the tail light in the tailgate but I cant get to the turn signal in the body...|||Check your owner%26#039;s manual. We just did my wife%26#039;s 2008, and there was a diagram in the manual that showed how to pull this off (Yours may be different).
On the 2008, with the tailgate opened, there are three narrow slots between the black plastic cowl inside the door jamb and the actual tail light assembly. You put a blade screwdriver in each of these, one at a time, %26quot;with a piece of electrical tape on it to prevent scratching,%26quot; and gently pry the cowl off. This exposes some screws that you remove to release the tail light assembly from the car. Once that%26#039;s done you can see where you twist the plastic bulb holder to release it from the light assembly. Replace the bulb, re-install the holder in the assembly, re-attach the assembly to the car and the cowl to the assembly, and you%26#039;re done.|||There is a tall and narrow removable access panel just inside, just behind the tail light assembly. The bulbs are easily found and remove with a quarter twist counter clockwise.
On the 2008, with the tailgate opened, there are three narrow slots between the black plastic cowl inside the door jamb and the actual tail light assembly. You put a blade screwdriver in each of these, one at a time, %26quot;with a piece of electrical tape on it to prevent scratching,%26quot; and gently pry the cowl off. This exposes some screws that you remove to release the tail light assembly from the car. Once that%26#039;s done you can see where you twist the plastic bulb holder to release it from the light assembly. Replace the bulb, re-install the holder in the assembly, re-attach the assembly to the car and the cowl to the assembly, and you%26#039;re done.|||There is a tall and narrow removable access panel just inside, just behind the tail light assembly. The bulbs are easily found and remove with a quarter twist counter clockwise.
How to change an 05 chevy cobalt tail light?
my tail light just went out so tomo im going to get a new bulb. I have no experience but it really cant be too hard. My brother who usually handles all my car problems is out of town. So if someone could give me detailed instuctions from beginning to end that%26#039;d be great thanks!|||get in the trunk and pull the carpet back from the rear of the taillight that needs fixed and you will see 3 or 4 wing nuts that you need to take off and then the light will pull completely out from the outside of the car and then you will see where the bulbs go.|||You can probably access the light from the trunk.
1) Remove the two screws revealed when the trunk lid is opened.
2) Unscrew upper cargo net anchor.
3) Pull back carpet wall, remove nut on threaded rod.|||Check in side your trunk...look for a panel that either comes apart by clips or screws. Pull the housing out carefully, your bulb should screw out..the whole thing should be self explanatory. Hope this was helpful.
1) Remove the two screws revealed when the trunk lid is opened.
2) Unscrew upper cargo net anchor.
3) Pull back carpet wall, remove nut on threaded rod.|||Check in side your trunk...look for a panel that either comes apart by clips or screws. Pull the housing out carefully, your bulb should screw out..the whole thing should be self explanatory. Hope this was helpful.
I need to know how to change the rear bulbs(tail lights) in a 99 Chevy Tahoe.?
Open the rear door. On the inside of the door frame their are 2 torx (looks like a star) screws, a T-15 is the size I believe. One to the top of the light cover and one to the bottom.|||going from memory there should be hex head screws on the outside of the lamp. One on the top one on the bottom. Take those out and pull the lamp right out. At least that is how the pickups are in those years.
How do I change the brake light bulb on a 2004 Dodge Durango?
The driver%26#039;s side brake light is out and I dont see how to get the tail light lens off to replace the bulb? HELP!!!!!!!!!!! THANKS|||If you can%26#039;t figure it out, then you can%26#039;t operate a screwdriver. There are 2 screws that hold the tail lamp in place. Once you remove those the tail lamp will %26quot;pop%26quot; out and then you can swap out the bulb. Any shop can do it in about 5 minutes.
How would I diagnose and change a burnt out light bulb (headlight/taillight) in my 1994 Crown Victoria?
My right turn signal lights up but does not blink. I have heard that this may be due to a burnt out light bulb. However, upon cursury inspection, all lights seem to work... so I think perhaps I need to take of the tail lenses and replace a bulb. It%26#039;s just that I%26#039;ve never done this before, so I was wondering how to go about this... Thank you for your help!|||the most common type of automtive bulb is a twist-type. What I mean by this, is the bulb should come loose by turning the plastic housing that sorrounds the bulb itself. then simply change bulbs, insert back into its hole, and turn back into place.|||Hello,
If all the bulbs are still lite up then your bulbs are fine. You may have a selanoid that is bad or the turn signal switch needs to be worn out.
If all the bulbs are still lite up then your bulbs are fine. You may have a selanoid that is bad or the turn signal switch needs to be worn out.
If anyone knows how to change a tail light in a 2003 lancer, id greatly appreciate it.?
When you go in thru the trunk and remove the panel you can not access the bulbs from there. I tried to remove the whole unit but it woulnt come off. So Im all out of ideas and I refuse to take it to the shop.|||only 2 ways to get to it either from inside the housing or in the trunk it should turn the housing which holds the bulb in the housing and it comes out of the rear of the lens assembly
How do you change the tail light for Toyota Sienna 2004 LE?
I need to know how to replace the brake bulb at the rear.
Thank You|||go to auto zone.com and use there repair manuals its free.just type in your vehicle.good luck|||Remove the old light, put in the new light.|||Unbolt the light fixture on the inside and pop the complete fixture out. The bulb can then be turned out and changed.
Thank You|||go to auto zone.com and use there repair manuals its free.just type in your vehicle.good luck|||Remove the old light, put in the new light.|||Unbolt the light fixture on the inside and pop the complete fixture out. The bulb can then be turned out and changed.
Want to know how to remove rear tail light on 89 chevy celebrity to change light?
need to check wires %26amp; bulb on 89 celebrity tail light|||The bulb %26quot;should%26quot; be able to be removed from inside.
Unplug it.
turn it 1/4, jiggle and pull.
You might have to remove some plastic cover to get to it.
But it%26#039;s pretty simple.|||I will assume you are talking about the bulb, not the entire housing/ lens. Open your trunk, you will see wires going to a socket in the interior housing. Rotate the socket about 1/4 turn to the left (you will feel it loosen), pull it straight out to check/replace the bulb. To reinstall, reverse the procedure.|||can you get to the bulb by opening the trunk?|||i bet your manual knows ;)
Unplug it.
turn it 1/4, jiggle and pull.
You might have to remove some plastic cover to get to it.
But it%26#039;s pretty simple.|||I will assume you are talking about the bulb, not the entire housing/ lens. Open your trunk, you will see wires going to a socket in the interior housing. Rotate the socket about 1/4 turn to the left (you will feel it loosen), pull it straight out to check/replace the bulb. To reinstall, reverse the procedure.|||can you get to the bulb by opening the trunk?|||i bet your manual knows ;)
How do I change a tail light on a VW Golf 1998?
I have the right bulb but no one in my area knows how to access the socket.|||Look in the owners manual. I%26#039;ve changed one before and it was so easy. All the bulbs for the tail lights are together.
You have to depress on 2 spring clips on either side of the bulb holder and pull all the bulbs out. Be careful to pull out straight because you can break all the other bulbs.
Press down on the bulb and turn to remove it. That%26#039;s it replace the bulb and push back the bulb holder.
Easy.
You have to depress on 2 spring clips on either side of the bulb holder and pull all the bulbs out. Be careful to pull out straight because you can break all the other bulbs.
Press down on the bulb and turn to remove it. That%26#039;s it replace the bulb and push back the bulb holder.
Easy.
How do I change the tail light on a 2005 Chevy Cobalt LT?
The 2005 Chevy Cobalt LT has a single, triangular tail lamp assembly on each rear corner of the vehicle. (Not the more common pair of circular lights on other models.)
Opening the trunk reveals two screws attaching the tail lamp assembly to the car. Removing the two screws allows the assembly to wiggle a little bit, but the assembly cannot be pulled away from the car to disconnect the wiring harness or access the bulbs.
The Pioneer sub woofer limits how far I can pull the trunk carpet wall back, but I have felt for any other retention clips, screws, or wire harnesses. I cannot find anything else to disconnect.
I have gradually increased my pulling force with no success. I have tried sliding the assembly in different directions to un-lock any slide-and-lock style retainers with no success. I have tried removing the passenger-side tail light assembly, but have the same problem.|||It%26#039;s under warranty take it to your local dealership and say fix it leave the subs they have to work around it.|||take the sub box out twist th harness and the bulb and it should come out|||Hello fellow Cobalt owner. Try posting your question in yourcobalt.com. Lots of helpful people on that site and plenty of do-it-yourselfers. Also, does the owners manual , page 5-51 help at all?|||www.autozone.com|||Backup Lamp Assembly Replacement
1
Cover, Backup Lamp
Tip Press the tab on the cover to remove from the decklid.
2
Nut, Backup Lamp (Qty: 3)
Tip If only replacing the bulb, turn the bulb socket assembly and pull out of the lamp assembly. This can be done from inside of the rear compartment lid, without removing the lamp from the vehicle.
Tighten 10 Nè·¯m (89 lb in)
3
Lamp Assembly, Backup
Tip Disconnect the electrical connector.
Tail Lamp Assembly Replacement
4
Nut, Tail Lamp (Qty: 3)
Tip If only replacing the bulb, turn the bulb socket assembly and pull out of the lamp assembly. This can be done from inside of the rear compartment, without removing the lamp assembly.
Tighten 10 Nè·¯m (89 lb in)
5
Lamp, Tail
Tip Disconnect the electrical connector to remove the lamp from the quarter panel.
Side Marker Lamp Assembly Replacement
6
Screw, Side Marker (Qty: 1)
Tighten 2 Nè·¯m (18 lb in)
7
Lamp, Side Marker
Tip Disconnect the electrical connector to remove the lamp from the fascia|||take it to a mechanic
Opening the trunk reveals two screws attaching the tail lamp assembly to the car. Removing the two screws allows the assembly to wiggle a little bit, but the assembly cannot be pulled away from the car to disconnect the wiring harness or access the bulbs.
The Pioneer sub woofer limits how far I can pull the trunk carpet wall back, but I have felt for any other retention clips, screws, or wire harnesses. I cannot find anything else to disconnect.
I have gradually increased my pulling force with no success. I have tried sliding the assembly in different directions to un-lock any slide-and-lock style retainers with no success. I have tried removing the passenger-side tail light assembly, but have the same problem.|||It%26#039;s under warranty take it to your local dealership and say fix it leave the subs they have to work around it.|||take the sub box out twist th harness and the bulb and it should come out|||Hello fellow Cobalt owner. Try posting your question in yourcobalt.com. Lots of helpful people on that site and plenty of do-it-yourselfers. Also, does the owners manual , page 5-51 help at all?|||www.autozone.com|||Backup Lamp Assembly Replacement
1
Cover, Backup Lamp
Tip Press the tab on the cover to remove from the decklid.
2
Nut, Backup Lamp (Qty: 3)
Tip If only replacing the bulb, turn the bulb socket assembly and pull out of the lamp assembly. This can be done from inside of the rear compartment lid, without removing the lamp from the vehicle.
Tighten 10 Nè·¯m (89 lb in)
3
Lamp Assembly, Backup
Tip Disconnect the electrical connector.
Tail Lamp Assembly Replacement
4
Nut, Tail Lamp (Qty: 3)
Tip If only replacing the bulb, turn the bulb socket assembly and pull out of the lamp assembly. This can be done from inside of the rear compartment, without removing the lamp assembly.
Tighten 10 Nè·¯m (89 lb in)
5
Lamp, Tail
Tip Disconnect the electrical connector to remove the lamp from the quarter panel.
Side Marker Lamp Assembly Replacement
6
Screw, Side Marker (Qty: 1)
Tighten 2 Nè·¯m (18 lb in)
7
Lamp, Side Marker
Tip Disconnect the electrical connector to remove the lamp from the fascia|||take it to a mechanic
How do you change a burnt out tail light in a 09 Buick Enclave?
My wife%26#039;s enclave has a burnt out taillight.. How do you change the bulb ? I don%26#039;t see how to take the lens off or remove the light Assembly. It is NOTHING like my 67 Firebird. HELP ?!|||take it to autozone and act (sic) like a dumb blonde, they may put it in for you|||very carefully
HELP!! HOW DO U CHANGE A BRAKE LIGHT BULB ON A 2006 EQUINOX?
Tell me how to get the cover off. I need to change a light bulb on a brake light on a 2006 chevy equinox!!! I mean in the tail light section? Help help help!!!!!|||If there are no screws on the outside.Open the trunk.You will need to take out or pull back the carpet like walls directly behind where the tail light is..There should be up to 4 plastic wing-nuts or 4 nuts.you will need to take off.If you can get to the bulb from the trunk go ahead,but you probably will need to take the entire tail light out.|||open up the hatch there should be 2 phillips head screws on the inside. if that isnt right try seeing if there is an access panel inside that will give you access to the back of the lights without actually taking the light off of the vehicle|||I dont know... but you should have sex with the chick ur doing it for
How do I change the break light on a nissan 2001 sentra?
my left back tail light went out I got the correct light bulb for it but can%26#039;t find the way to replace it help with some detailed steps if you can don%26#039;t want to take to shop just to change a light bulb.|||nissans are fairly simple just got to the trunk look and you should see some plastic plugs. remove those and remove the nuts that are holding the tail light and replace. if not this steps, then just remove the cover and replace the bulb from the inside the trunk brehind the light
How do toy change the break light on a nissan 2001 sentra?
my left back tail light went out I got the correct light bulb for it but can%26#039;t find the way to replace it help with some detailed steps if you can don%26#039;t want to take to shop just to change a light bulb.|||Look in the trunk on some cars you change from inside the trunk by pulling out the socket. Hope it helps good luck.
How do you get the tail light lens off an 03' town and country to change the bulb???
If it is anything like my 2000 Grand Caravan, you open the rear liftgate and look at the taillight assembly. There should be two phillips head screws. Remove those and rotate the lens out and away from the inside of the van. Be careful not to snap the tab off the opposite side of the lense.|||Look inside. Most now change without any tools needed.
How do you replace a tail light (brake) bulb on a 2004 Jeep Grand Cherokee?
I opened the liftgate and removed the two phillips head screws from the side of the housing, however I can%26#039;t move the light casing to get in and change the bulb.|||You will most likely not find an interior access to the lights ,,, you must remove the screws on the outside and remove the casing to get to the bulbs ... Most yrs did not have any way of gaining access from the inside ... i%26#039;m not sure if the owners manual shows this feature but it would be great to have a shop manual or at the very least a Haynes or Chiltons manual for reference... Good Luck|||Look for two more screws somewhere outside the vehicle. Also look for an access pannel just inside the back at the same level of the taillights. If there is one, you may be able to reach in and change the bulbs right there.|||After obtaining the correct light bulb-- an auto store or the dealership can tell you-- open the back hatch. On the inside back wall is where you will find access to the bulbs. I don%26#039;t know if you take the interior wall off or a open a door, but try gently (It%26#039;s easy to mark things up if you use a screwdriver to pry it off). You may even have to unscrew this. Make sure you put the burnt out bulb away from you in the garbage--don%26#039;t want to accidentally reinstall that. Plug in the new one. And reseal the compartment. Then make sure you get behind the wheel and press on the brakes with the jeep running and a friend posted at the back to notify you if its the right light bulb you replaced--and not a night driving one..
About the S 10 p/u, year 2000, how to remove the rear tail light lens to change bulb that is out. thank you.?
open the tailgate and look for the screws holding the housing|||If you let the tail gate down, look through where it latches. One screw will be there and the other is about 4 inches below it. Once they are out, you can pull the tail light assembly out and change the bulb.
I have owned 2 S-10%26#039;s
I have owned 2 S-10%26#039;s
I can't figure out how to change my 2007 ford focus tail light bulb.?
yes i know there is one srew and clip, but i cant figure out how to get the clip undone. any help would be greatly appreciated.|||i have an 05 the same problem you have to pull the clip loose with out breaking it ive change mine 3 times without it breaking
How do i change my rear tail light bulbs?
1985 Chrysler 5th ave; the bulb is broke and i don%26#039;t know how to change it.|||i learned this today in drivers ed :). Usually the steps to perform this task is in the manual. It is specific to every car. If you can not figure it out I recommend going to a mantinence shop, because your license can be taken away because of this, and you can be fined over 200$. This website might also help http://www.ehow.com/how_2631_replace-tai鈥?/a> . I hope this helps :) Good luck.|||Open the trunk, twist the big plastic piece right behind where the bulb should be counterclockwise, pull it out of the housing and there%26#039;s the bulb. Twist out the bulb, put new one in, and put it back together the way you took it apart. Easy.|||I don%26#039;t know that model but look for access in the trunk.
How to change the tail light bulb on a 2007 chevy silverado w/utility bed?
I need an image of the assembly if possible. I have already tried the checy website. It is not the same as a regular bed.|||Different lights on different beds. Is this a sealed unit light assembly mounted in a rubber grommet like on an 18 wheeler trailer? I have seen
some of the new light assembly%26#039;s that are the LED assembly%26#039;s that
have a metal ring riveted to the body to stop theft.
some of the new light assembly%26#039;s that are the LED assembly%26#039;s that
have a metal ring riveted to the body to stop theft.
How do I change the bulb in the tail light of a 2005 Volkswage GTI?
My mom zips me to school, wrestling practice and just about everywhere else in this little car, so I want to do something nice for her. I just can%26#039;t seem to get the bulb out. Can anyone help me out and give me step-by-step instructions? Thanks!|||Mark L,
I had a similar problem with my car and i went to Auto Zone and i purchased the bulb from them and they installed it for me at no charge.....I have a freind that did the same thing but at O%26#039;Reillys and it was free also, but you have to purchase the bulb from them.....
I had a similar problem with my car and i went to Auto Zone and i purchased the bulb from them and they installed it for me at no charge.....I have a freind that did the same thing but at O%26#039;Reillys and it was free also, but you have to purchase the bulb from them.....
Changing 1966 cadillac deville tail light bulbs?Where do you access the bulbs to change them.?
I can see the bulbs up underneath but there is very little room.How do you change these bulbs without trying to get your hand up and under the bumper?|||SOMETIMES FROM INSIDE THE TRUNK PULL THE LINER BACK AND HAVE A PEEK...|||a 1966 Caddy probably has screws holding the lens on, take a look and if it does just remove the screws and then pull the lens off to access the bulbs, if there are no screws, you will have to access the bulbs from inside the trunk.|||as with nearly any car from the sxties you have to remove the whole assembly and remove th screws in the back which hold the colored lenses on
How to change BMW 325 tail light bulb?
Check for thumb screws just inside the trunk behind the tail light.Take the screws loose and pull on the light assembly to get to the bulbs.
How do I remove tail light cover on 2006 Silverado to change break light bulb.?
there should be some screws inside the bed to loosen the lens
How do you change the tail light bulbs on a 2002 Pontiac Firebird? ?
I have a 2002 Pontiac Firebird and my tail lights are out. I just don%26#039;t know how to replace them. If someone could please tell me, that%26#039;d be great!|||Unable to find it in your owner%26#039;s manual?
Open rear hatch, remove access panels to allow you to reach the tail light bulbs. They are located forward of the tail light assemblies on the inside bolster within the trunk enclosure.
Most of the bulbs will be a 1/4 turn counter clockwise to remove from their housing and the bulb may be a straight pull from it%26#039;s socket.
Get in there as it only takes a few minutes to accomplish.
Open rear hatch, remove access panels to allow you to reach the tail light bulbs. They are located forward of the tail light assemblies on the inside bolster within the trunk enclosure.
Most of the bulbs will be a 1/4 turn counter clockwise to remove from their housing and the bulb may be a straight pull from it%26#039;s socket.
Get in there as it only takes a few minutes to accomplish.
How to change a tail light bulb 2005 jeep grand cherokee?
open the rear hatch there will be two screws visible take them out pull the housing and it will pop out turn the grey socket to remove the bulb and pop it back in install the two screws Back in and done it takes about five minutes per side
How to change the tail light bulb on a 2007 Prius?
RTFM (Read The Fine Manual).|||you either have to get to it inside the trunk or take the lens off.
How do i access the tail light bulbs to change on a 2001 nissan frontier truck?
My tail light bulbs are going out. How do i change them?|||there should be two screws on the inside of the plastic cover, let the tail gate down and look on that side, the then two on the other side....take those out and it should pop off|||pull back the bed liner. two screws.
How to change a burnt out brake light bulb?
How do you change a tail light bulb in a car?|||you need to declare the car and model to find this out.
Some older cars- take off the lens cap screws and change the bulb.
newer cars- from the trunk.
check the owners manual or just google
%26quot;change brake light 1999 caravan%26quot;|||go in the trunk and pull the carpet away from the back of the light...there is usually screws or grommets that you have to pop off and then the bulb slides out. it connects to its socket almost like when you connect a regular cord to an extension cord. the bulb will have the style of bulb that it is. Make sure you get this same kind. If you are really unsure go to an auto parts store and they will help you out.|||how about auto zone and maybe they will do it for ya
Some older cars- take off the lens cap screws and change the bulb.
newer cars- from the trunk.
check the owners manual or just google
%26quot;change brake light 1999 caravan%26quot;|||go in the trunk and pull the carpet away from the back of the light...there is usually screws or grommets that you have to pop off and then the bulb slides out. it connects to its socket almost like when you connect a regular cord to an extension cord. the bulb will have the style of bulb that it is. Make sure you get this same kind. If you are really unsure go to an auto parts store and they will help you out.|||how about auto zone and maybe they will do it for ya
How to change a tail light bulb for a 2006 Chevrolet Cobalt?
Remove the bulb and install new bulb, if you cant do that go to a dealer and pay them half hour labor plus the bulb 60 bucks.|||open the trunk and pull the carpet back in back of the rear light and you will see wing nuts that you unscrew and then take them off and pull the complete light assembly out and you will then see the bulbs.|||You can drive your car to the chevrolet dealer service department and ask them. They are usually willing to explain how to do minor maintenace work. I%26#039;ve done this on several occassions.|||i dnt think theyre different from any other car ull have to open the trunk, move the carpet liner and twist and pull out the light socket, then put the new one in and put it all back.|||you better go to a good,, auto repair shop,, or a car repair shop, something like that, CAr service, its really hard, and,, they can change it for some money.|||generally in the new vehicles there are either 2 or 3 plastic wing nuts that you can turn and your tail light assemble should slide right out, replace bulb put assemble back in and tighten wing nuts|||most cars..open trunk and look...pop out socket and change it. get auto parts guy to help..advance auto
Changing a tail light bulb on a Ford Ka?
I need to change the right tail light bulb on my Ford Ka but I am at a loss as to how to do it, what type of bulb to get and where I can get it. Anyone help?|||I agree with Rachel there, you should go to halfords and they will find the right bulb for your car and change it for you for a small price, its only æ‹¢2 or something!! :)|||go to halfords. in the lights section they ahve a guide. You find your car and get the code. Look for that code on the lights you need.
for fitting you go into the boot. At the back of where your lights are you should be able to pull of the casing/lining of the boot to get inside.
Then its just like changing a lightbulb!!!!!!!|||Halfords too expensive??? You%26#039;re looking to purchase ONE bulb! Obviously this is causing you concern so I would have thought the most sensible thing to do is to find out from Halfords which bulb you need and buy it when you are there. If it costs you 20 pence more, at least you%26#039;ve solved your problem. Alternatively take the existing bulb out and get to an alternative shop. Nothing difficult about that, surely!
for fitting you go into the boot. At the back of where your lights are you should be able to pull of the casing/lining of the boot to get inside.
Then its just like changing a lightbulb!!!!!!!|||Halfords too expensive??? You%26#039;re looking to purchase ONE bulb! Obviously this is causing you concern so I would have thought the most sensible thing to do is to find out from Halfords which bulb you need and buy it when you are there. If it costs you 20 pence more, at least you%26#039;ve solved your problem. Alternatively take the existing bulb out and get to an alternative shop. Nothing difficult about that, surely!
Anyone know how to change a tail light bulb on a 2002 altima?
Open the trunk, pull back the carpeting covering the rear of the lights, you may need to remove a few screws, twist the socket to loosen it, pull it out, remove the blown bulb, replace it with the new one, put the socket back in and twist it the other way to tighten it, put the carpeting back|||Open your trunk. Open the access/circuit panel on the back of the tail light. Replace the bulb. Pop the panel back on. Close the trunk.
How do i change a tail light bulb on a pontiac g6 v6 2008?
i cant figure out how to access the bulb. cant go through the trunk, and im afraid to take off the red glass on the outside.|||To better help you; take it to the GM dealership (or any for that matter) and they will replace the tail light under warranty. GM will replace anything (except wiper blades) for 3 years or 36,000 miles bumper to bumper.
Hope that helps you!|||You probably need to remove the carpeting and side mats in the trunk before you can access the fasteners for the tail light housings. Most sedans that I have had (GM and Ford both) have the tail light fasteners hidden my that stuff.
Hope that helps you!|||You probably need to remove the carpeting and side mats in the trunk before you can access the fasteners for the tail light housings. Most sedans that I have had (GM and Ford both) have the tail light fasteners hidden my that stuff.
Is it easy to change a tail light bulb on a 96 acura integra?
Can anybody tell me how to change one?|||I dont think it%26#039;s very hard, but i%26#039;d recommend you to head to repair or maintenance manual...|||it%26#039;s real easy to do your self. But you could always go to your local parts store (autozone or pep boys) and ask if someone ther will do it for you.
Usually as long as you buy the bulbs there they will be more than helpfull.|||I had a 91 and there was access to the tailights in the trunk. I can%26#039;t believe they made it hard to get to.|||Yes, you need to access the housing from the trunk. Being sure you have the right bulb is half the battle, the wrong bulb will work, but not properly.|||in the trunk there is a liner covering it, you have to pull that down and would probably be easier to take out the whole tail light and then pull out the correct bulb and replace it. 15 min if you know how.
Usually as long as you buy the bulbs there they will be more than helpfull.|||I had a 91 and there was access to the tailights in the trunk. I can%26#039;t believe they made it hard to get to.|||Yes, you need to access the housing from the trunk. Being sure you have the right bulb is half the battle, the wrong bulb will work, but not properly.|||in the trunk there is a liner covering it, you have to pull that down and would probably be easier to take out the whole tail light and then pull out the correct bulb and replace it. 15 min if you know how.
I know I am dumb, but how and the heck do you change a tail light bulb on a GMC 2000 Yukon?
When I use the left turn signal, I get a rapid flash. The front signal works, but tha rear and left rear brake light does not. I went to Pep Boys and bought replacement bulbs, but the heck if I can figure out how to get the lense cover off so I can replace the blown bulb.
Anybody have any experience? There does not seem to be any screw holes on the outside -- Is this a dealer or repair shop job? I need some help, any comments are appreciated and I feel like a goof for asking such a simple question.
Thanks!|||OPen the tail gate. There are two torx type screws holding the light assembly on.
Remove them, and give it a tug.
The bulb holders need to be turned about 1\4 turn, and pulled out.|||With that kind of gas milage, a tail light is the least of your concerns!|||YOU ARE NOT DUMB, That would be kinda difficult if you have never did it before and if you are in a rush. Just wait until you are less aggravated by it chill out for a moment, Then If and only if your feel you can take care of it then try again, If not just take it to Auto Zone when they are not so busy, And one of the guys in there will change it for ya. Unless you know someone else that will do it. I watch some one do that sort of thing before and It was pretty darn work, In the dark to but we got through with it. So just try that. Take Care|||yea
Anybody have any experience? There does not seem to be any screw holes on the outside -- Is this a dealer or repair shop job? I need some help, any comments are appreciated and I feel like a goof for asking such a simple question.
Thanks!|||OPen the tail gate. There are two torx type screws holding the light assembly on.
Remove them, and give it a tug.
The bulb holders need to be turned about 1\4 turn, and pulled out.|||With that kind of gas milage, a tail light is the least of your concerns!|||YOU ARE NOT DUMB, That would be kinda difficult if you have never did it before and if you are in a rush. Just wait until you are less aggravated by it chill out for a moment, Then If and only if your feel you can take care of it then try again, If not just take it to Auto Zone when they are not so busy, And one of the guys in there will change it for ya. Unless you know someone else that will do it. I watch some one do that sort of thing before and It was pretty darn work, In the dark to but we got through with it. So just try that. Take Care|||yea
How to change the tail light bulb On a honda del sol?
I need like a pic or a good discripition on how to remove the asembly to get to the light! thank you very much.|||Remove the panel in the trunk, there should be screws. Don%26#039;t be afraid to use a little force.. It%26#039;s pretty simple.. I believe they%26#039;re clipped on also.
How to change tail light bulb in 2001 vw beetle?
how to take out tail light assembly to replace the bulb|||if you open the back and pull the carpet back you can see the bolts holding it on.
How do you change a tail light bulb in a Pontiac Aztec?
The tail light bulb went out and needs to be replaced.|||Lift the rear hatch you will see 2 torex (sp) screws. Take them out and the tail light should just slide out then remove the bulbs and replace them.|||You actually bought a pontiac aztec?|||go buy a new car|||You don%26#039;t . You get rid of it right now.|||The owner%26#039;s manual should tell you exactly how to do it
How to change tail light bulb from a ford excort?
When you open the trunk you should see two screws. Remove them and the lamp assembly should come out. When you get it out twist and remove the bulb sockets from the housing and replace the bulb. Just a guess because I don%26#039;t know what year it is.
How to change tail light bulb-2005 toyota sienna?
I can%26#039;t figure out how to get at the tail light bulb in a mini van sienna. no access panel inside? do i take off the bolts that hold the actuall plastic light?|||try www.toyotaowners.com
it%26#039;s made by toyota
i needed my front headlight replaced, and it showed how to do it.
hope i%26#039;ve helped|||On some vehicles you need to remove panels to get to the light bulbs.
I know this is stupid but I didn%26#039;t engineer the thing.
Buy American|||This will probably be the best move, -- however look at the screws, they have helped by putting %26quot;torx%26quot; screws in most tail light assemblies, so that you have to buy a special screwdriver to get screws out!
And of course if you can see the screws, you are in good condition, and if no screws visible from outside, then you have to pull side panel inside loose to get behind assembly and take screws or nuts off, -- but of course if you are behind, -- you can just pull out sockets and change bulbs anyway (leaving light assembly in place)!
it%26#039;s made by toyota
i needed my front headlight replaced, and it showed how to do it.
hope i%26#039;ve helped|||On some vehicles you need to remove panels to get to the light bulbs.
I know this is stupid but I didn%26#039;t engineer the thing.
Buy American|||This will probably be the best move, -- however look at the screws, they have helped by putting %26quot;torx%26quot; screws in most tail light assemblies, so that you have to buy a special screwdriver to get screws out!
And of course if you can see the screws, you are in good condition, and if no screws visible from outside, then you have to pull side panel inside loose to get behind assembly and take screws or nuts off, -- but of course if you are behind, -- you can just pull out sockets and change bulbs anyway (leaving light assembly in place)!
How do I change light bulb on tail light of 1996 Fiat punto?
Thought it would be easy but can%26#039;t work out how to get to the bulb or get plastic light covers off. Any clues you lot?|||They are all wrong. Open the boot. Working from inside the boot, there are 2 round plastic covers top and bottom where the light fitting are on the body. prise out the covers with a small screwdriver. you will then find little metal nuts that hold the light fitting in place. undo these nuts anti clockwise. they are usually only hand tight, however I have come across some that had to be undone with a 14mm socket or a pliers. Once thes nuts are removed, the whole light fitting can be pulled away from the body of the car. You the squeeze the plastic lugs and pull the bulb holder away from the light Lens.|||Well if you can see screws on the cover then you remove the cover and change the bulb if no the you must change the whole set.
I think it should do it.
Regards,
KBK|||In the boot there are some plastic lugs on the lamp compress those and the base of the lamp comes out and you remove the bulb easily then
I think it should do it.
Regards,
KBK|||In the boot there are some plastic lugs on the lamp compress those and the base of the lamp comes out and you remove the bulb easily then
How do I change tail light bulb 2006 ford focus zx3?
I can%26#039;t figure out how to change the light bulb! The manual doesn%26#039;t give proper instructions and my dealer just closed! HELP!|||i%26#039;d try to open the trunk. there should be a couple screws in there. take them out and pull the tail-light away from the trunk. to take the burnt light out grab twist and pull.
Subscribe to:
Posts
(Atom)